linuxcnc 2.7.14, stretch amd64, 4.9.0-8-rt-amd64, debian RT-PREEMPT, 19.11.2018 - funkčné
sudo gedit /etc/security/limits.conf
pridať riadok "* - memlock 20480"
apt-get install linux-image-4.9.0-8-rt-amd64 firmware-linux-free irqbalance libnuma1 libnuma-dev
apt-get install linux-headers-4.9.0-8-rt-amd64 linux-kbuild-4.9 intltool
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.6-dev tk8.6-dev tclx autoconf libgtk2.0-dev
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/stretch/2.7-uspace/source/linuxcnc_2.7.14.tar.xz
tar -xvf linuxcnc_2.7.14.tar.xz
mv build linuxcnc-2.7.14
cd linuxcnc-2.7.14/src
pre xhc-hb04 zmeniť hexa kód z 10CE:EB70 na 10CE:EB6E
gedit hal/user_comps/xhc-hb04.cc
./autogen.sh
./configure --enable-non-distributable=yes --prefix=/usr --with-realtime=uspace
make clean
make
make install
linuxcnc 2.7.13, stretch amd64, 4.9.0-6-rt-amd64, debian RT-PREEMPT, 20.6.2018 - funkčné
sudo gedit /etc/security/limits.conf
pridať riadok "* - memlock 20480"
apt-get install linux-image-4.9.0-6-rt-amd64 firmware-linux-free irqbalance libnuma1 libnuma-dev
apt-get install linux-headers-4.9.0-6-rt-amd64 linux-kbuild-4.9 intltool
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.6-dev tk8.6-dev tclx autoconf libgtk2.0-dev
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/stretch/2.7-uspace/source/linuxcnc_2.7.13.tar.xz
tar -xvf linuxcnc_2.7.13.tar.xz
mv build linuxcnc-2.7.13
cd linuxcnc-2.7.13/src
pre xhc-hb04 zmeniť hexa kód z 10CE:EB70 na 10CE:EB6E
gedit hal/user_comps/xhc-hb04.cc
./autogen.sh
./configure --enable-non-distributable=yes --prefix=/usr --with-realtime=uspace
make clean
make
make install
linuxcnc 2.7.12, stretch amd64, 4.9.0-6-rt-amd64, debian RT-PREEMPT, 23.2.2018 - funkčné
sudo gedit /etc/security/limits.conf
pridať riadok "* - memlock 20480"
apt-get install linux-image-4.9.0-6-rt-amd64 firmware-linux-free irqbalance libnuma1 libnuma-dev
apt-get install linux-headers-4.9.0-6-rt-amd64 linux-kbuild-4.9 intltool
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.6-dev tk8.6-dev tclx autoconf libgtk2.0-dev
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/stretch/2.7-uspace/source/linuxcnc_2.7.12.tar.xz
tar -xvf linuxcnc_2.7.12.tar.xz
mv build linuxcnc-2.7.12
cd linuxcnc-2.7.12/src
pre xhc-hb04 zmeniť hexa kód z 10CE:EB70 na 10CE:EB6E
gedit hal/user_comps/xhc-hb04.cc
./autogen.sh
./configure --enable-non-distributable=yes --prefix=/usr --with-realtime=uspace
make clean
make
make install
linuxcnc 2.7.11, stretch amd64, 4.9.0-3-rt-amd64, debian RT-PREEMPT, 1.8.2017 - funkčné
sudo gedit /etc/security/limits.conf
pridať riadok "* - memlock 20480"
apt-get install linux-image-4.9.0-3-rt-amd64 firmware-linux-free irqbalance libnuma1 libnuma-dev
apt-get install linux-headers-4.9.0-3-rt-amd64 libsan0 linux-kbuild-3.16
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.6-dev tk8.6-dev tclx autoconf libgtk2.0-dev
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/jessie/2.7-uspace/source/linuxcnc_2.7.11.tar.xz
tar -xvf linuxcnc_2.7.11.tar.xz
mv build linuxcnc-2.7.11
cd linuxcnc-2.7.11/src
pre xhc-hb04 zmeniť hexa kód z 10CE:EB70 na 10CE:EB6E
gedit hal/user_comps/xhc-hb04.cc
./autogen.sh
./configure --enable-non-distributable=yes --prefix=/usr --with-realtime=uspace
make
make install
linuxcnc 2.7.11, jessie amd64, 3.16.0-9-rtai-amd64, rtai-5.0~test1, 29.7.2017 - funkčné
sudo gedit /etc/apt/sources.list
pridať "deb http://linuxcnc.org jessie base"
apt-get update
apt-get install linux-image-3.16.0-9-rtai-amd64 firmware-linux-free irqbalance libnuma1
apt-get install libnuma-dev rtai-modules-3.16.0-9
apt-get install linux-headers-3.16.0-9-rtai-amd64 linux-headers-3.16.0-9-common-rtai
apt-get install cpp-4.8 gcc-4.8 libsan0 libgcc-4.8-dev linux-compiler-gcc-4.8-x86 linux-kbuild-3.16
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.6-dev tk8.6-dev tclx autoconf libgtk2.0-dev
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/jessie/2.7-uspace/source/linuxcnc_2.7.11.tar.xz
tar -xvf linuxcnc_2.7.11.tar.xz
mv build linuxcnc-2.7.11
cd linuxcnc-2.7.11/src
pre xhc-hb04 zmeniť hexa kód z 10CE:EB70 na 10CE:EB6E
gedit hal/user_comps/xhc-hb04.cc
./autogen.sh
./configure --enable-non-distributable=yes --prefix=/usr --with-realtime=/usr/realtime-3.16.0-9-rtai-amd64
make
make install
linuxcnc 2.7.10, jessie amd64, 3.16.0-9-rtai-amd64, rtai-5.0~test1, 27.7.2017 - funkčné
sudo gedit /etc/apt/sources.list
pridať "deb http://linuxcnc.org jessie base"
apt-get update
apt-get install linux-image-3.16.0-9-rtai-amd64 firmware-linux-free irqbalance libnuma1
apt-get install libnuma-dev rtai-modules-3.16.0-9
apt-get install linux-headers-3.16.0-9-rtai-amd64 linux-headers-3.16.0-9-common-rtai
apt-get install cpp-4.8 gcc-4.8 libsan0 libgcc-4.8-dev linux-compiler-gcc-4.8-x86 linux-kbuild-3.16
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.6-dev tk8.6-dev tclx autoconf libgtk2.0-dev
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/jessie/2.7-uspace/source/linuxcnc_2.7.10.tar.xz
tar -xvf linuxcnc_2.7.10.tar.xz
mv build linuxcnc-2.7.10
cd linuxcnc-2.7.10/src
pre xhc-hb04 zmeniť hexa kód z 10CE:EB70 na 10CE:EB6E
gedit hal/user_comps/xhc-hb04.cc
./autogen.sh
./configure --enable-non-distributable=yes --prefix=/usr --with-realtime=/usr/realtime-3.16.0-9-rtai-amd64
make
make install
linuxcnc 2.7.9, jessie amd64, 3.16.0-9-rtai-amd64, rtai-5.0~test1, 26.7.2017 - funkčné
sudo gedit /etc/apt/sources.list
pridať "deb http://linuxcnc.org jessie base"
apt-get update
apt-get install linux-image-3.16.0-9-rtai-amd64 firmware-linux-free irqbalance libnuma1
apt-get install libnuma-dev rtai-modules-3.16.0-9
apt-get install linux-headers-3.16.0-9-rtai-amd64 linux-headers-3.16.0-9-common-rtai
apt-get install cpp-4.8 gcc-4.8 libsan0 libgcc-4.8-dev linux-compiler-gcc-4.8-x86 linux-kbuild-3.16
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.6-dev tk8.6-dev tclx autoconf libgtk2.0-dev
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/jessie/2.7-uspace/source/linuxcnc_2.7.9.tar.xz
tar -xvf linuxcnc_2.7.9.tar.xz
mv build linuxcnc-2.7.9
cd linuxcnc-2.7.9/src
pre xhc-hb04 zmeniť hexa kód z 10CE:EB70 na 10CE:EB6E
gedit hal/user_comps/xhc-hb04.cc
./autogen.sh
./configure --enable-non-distributable=yes --prefix=/usr --with-realtime=/usr/realtime-3.16.0-9-rtai-amd64
make
make install
linuxcnc 2.7.8, jessie amd64, 3.16.0-9-rtai-amd64, rtai-5.0~test1, 12.11.2016 - funkčné
sudo gedit /etc/apt/sources.list
pridať "deb http://linuxcnc.org jessie base"
apt-get update
apt-get install linux-image-3.16.0-9-rtai-amd64 firmware-linux-free irqbalance libnuma1
apt-get install libnuma-dev rtai-modules-3.16.0-9
apt-get install linux-headers-3.16.0-9-rtai-amd64 linux-headers-3.16.0-9-common-rtai
apt-get install cpp-4.8 gcc-4.8 libsan0 libgcc-4.8-dev linux-compiler-gcc-4.8-x86 linux-kbuild-3.16
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.6-dev tk8.6-dev tclx autoconf libgtk2.0-dev
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/jessie/2.7-uspace/source/linuxcnc_2.7.8.tar.xz
tar -xvf linuxcnc_2.7.8.tar.xz
mv build linuxcnc-2.7.8
cd linuxcnc-2.7.8/src
pre xhc-hb04 zmeniť hexa kód z 10CE:EB70 na 10CE:EB6E
gedit hal/user_comps/xhc-hb04.cc
./autogen.sh
./configure --enable-non-distributable=yes --prefix=/usr --with-realtime=/usr/realtime-3.16.0-9-rtai-amd64
make
make install
linuxcnc 2.7.7, jessie amd64, 3.16.0-9-rtai-amd64, rtai-5.0~test1, 19.9.2016 - funkčné
sudo gedit /etc/apt/sources.list
pridať "deb http://linuxcnc.org jessie base"
apt-get update
apt-get install linux-image-3.16.0-9-rtai-amd64 firmware-linux-free irqbalance libnuma1
apt-get install libnuma-dev rtai-modules-3.16.0-9
apt-get install linux-headers-3.16.0-9-rtai-amd64 linux-headers-3.16.0-9-common-rtai
apt-get install cpp-4.8 gcc-4.8 libsan0 libgcc-4.8-dev linux-compiler-gcc-4.8-x86 linux-kbuild-3.16
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.6-dev tk8.6-dev tclx autoconf libgtk2.0-dev
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/wheezy/2.7-rtai/source/linuxcnc_2.7.7.tar.gz
tar -xvf linuxcnc_2.7.7.tar.gz
mv build linuxcnc
cd linuxcnc/src
./autogen.sh
./configure --prefix=/usr --with-realtime=/usr/realtime-3.16.0-9-rtai-amd64
make
make install
linuxcnc 2.7.7, wheezy i386, 3.8.13, rtai-3.9.262, 16.9.2016 - nefunkčné, rtapi!, shm!
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.5-dev tk8.5-dev tclx
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/wheezy/2.7-rtai/source/linuxcnc_2.7.7.tar.gz
tar -xvf linuxcnc_2.7.7.tar.gz
mv build linuxcnc
cd linuxcnc/src
./autogen.sh
./configure --prefix=/usr --with-realtime=/usr/rtai --enable-non-distributable=yes
make
make install
linuxcnc 2.7.6, wheezy i386, 3.8.13, rtai-3.9.262, 16.9.2016 - nefunkčné, rtapi!, shm!
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.5-dev tk8.5-dev tclx
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/wheezy/2.7-rtai/source/linuxcnc_2.7.6.tar.gz
tar -xvf linuxcnc_2.7.6.tar.gz
mv build linuxcnc
cd linuxcnc/src
./autogen.sh
./configure --prefix=/usr --with-realtime=/usr/rtai --enable-non-distributable=yes
make
make install
linuxcnc 2.7.5, wheezy i386, 3.8.13, rtai-3.9.262, 16.9.2016 - nefunkčné, rtapi!, shm!
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.5-dev tk8.5-dev tclx
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/wheezy/2.7-rtai/source/linuxcnc_2.7.5.tar.gz
tar -xvf linuxcnc_2.7.5.tar.gz
mv build linuxcnc
cd linuxcnc/src
./autogen.sh
./configure --prefix=/usr --with-realtime=/usr/rtai --enable-non-distributable=yes
make
make install
linuxcnc 2.7.4, jessie i386, 3.16.0-9-rtai-686-pae, rtai-5.0~test1, 14.5.2016 - funkčné
sudo gedit /etc/apt/sources.list
pridať "deb http://linuxcnc.org jessie base"
apt-get update
apt-get install irqbalance libnuma1 libnuma-dev rtai-modules-3.16.0-9
apt-get install linux-image-3.16.0-9-rtai-686-pae linux-headers-3.16.0-9-rtai-686-pae
apt-get install firmware-linux-free gcc-4.8 linux-build-3.16 linux-compiler-gcc-4.8-x86
apt-get install libgcc-4.8-dev
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.6-dev tk8.6-dev tclx autoconf libgtk2.0-dev
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/wheezy/2.7-rtai/source/linuxcnc_2.7.4.tar.gz
tar -xvf linuxcnc_2.7.4.tar.gz
mv build linuxcnc
cd linuxcnc/src
./autogen.sh
./configure --prefix=/usr --with-realtime=/usr/realtime-3.16.0-9-rtai-686-pae
make
make install
linuxcnc 2.7.4, wheezy i386, 3.8.13, rtai-3.9.262, 13.5.2016 - nefunkčné, rtapi!, shm!
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.5-dev tk8.5-dev tclx
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/wheezy/2.7-rtai/source/linuxcnc_2.7.4.tar.gz
tar -xvf linuxcnc_2.7.4.tar.gz
mv build linuxcnc
cd linuxcnc/src
./autogen.sh
./configure --prefix=/usr --with-realtime=/usr/rtai
make
make install
linuxcnc 2.7.3, wheezy i386, 3.8.13, rtai-3.9.262, 13.5.2016 - funkčné
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.5-dev tk8.5-dev tclx
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/wheezy/2.7-rtai/source/linuxcnc_2.7.3.tar.gz
tar -xvf linuxcnc_2.7.3.tar.gz
mv build linuxcnc
cd linuxcnc/src
./autogen.sh
./configure --prefix=/usr --with-realtime=/usr/rtai
make
make install
linuxcnc 2.7.2, wheezy i386, 3.8.13, rtai-3.9.262, 12.5.2016 - funkčné
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.5-dev tk8.5-dev tclx
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/wheezy/2.7-rtai/source/linuxcnc_2.7.2.tar.gz
tar -xvf linuxcnc_2.7.2.tar.gz
mv build linuxcnc
cd linuxcnc/src
./autogen.sh
./configure --prefix=/usr --with-realtime=/usr/rtai
make
make install
linuxcnc 2.7.1, wheezy i386, 3.8.13, rtai-3.9.262, 12.5.2016 - funkčné
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.5-dev tk8.5-dev tclx
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/wheezy/2.7-rtai/source/linuxcnc_2.7.1.tar.gz
tar -xvf linuxcnc_2.7.1.tar.gz
mv build linuxcnc
cd linuxcnc/src
./autogen.sh
./configure --prefix=/usr --with-realtime=/usr/rtai
make
make install
linuxcnc 2.7.0, wheezy i386, 3.8.13, rtai-3.9.262, 16.9.2015 - funkčné
apt-get -y install bwidget libreadline-dev libudev-dev
apt-get -y install tcl8.5-dev tk8.5-dev tclx
apt-get -y install libtk-img libmodbus-dev libusb-1.0-0-dev
apt-get -y install python-tk python-dev python-glade2 libboost-python-dev
wget http://www.linuxcnc.org/dists/wheezy/2.7-rtai/source/linuxcnc_2.7.0.tar.gz
tar -xvf linuxcnc_2.7.0.tar.gz
mv build linuxcnc
cd linuxcnc/src
./autogen.sh
./configure --prefix=/usr --with-realtime=/usr/rtai
make
make install
linuxcnc 2.7.0, wheezy i386, 3.4.55, rtai-3.9.262, 15.9.2015 - funkčné
apt-get -y install bwidget
apt-get -y install libreadline-dev
apt-get -y install tcl8.5-dev tk8.5-dev tclx
apt-get -y install libtk-img
apt-get -y install python-tk python-dev python-glade2
apt-get -y install libmodbus-dev
apt-get -y install libusb-1.0-0-dev
apt-get -y install libboost-python-dev
wget http://www.linuxcnc.org/dists/wheezy/2.7-rtai/source/linuxcnc_2.7.0.tar.gz
tar -xvf linuxcnc_2.7.0.tar.gz
mv build linuxcnc
cd linuxcnc/src
./autogen.sh
./configure --prefix=/usr --with-realtime=/usr/rtai
make
make install
linuxcnc 2.6.8, wheezy i386, 3.8.13, rtai-4.1, 22.7.2015 - vysoké latency - nepoužiteľné
apt-get -y install bwidget
apt-get -y install libreadline-dev
#apt-get -y install tcl8.5-dev tk8.5-dev
apt-get -y install libtk-img
apt-get -y install python-tk python-dev python-glade2
apt-get -y install libmodbus-dev
apt-get -y install libusb-1.0-0-dev
apt-get -y install libboost-python-dev
git clone -b v2.6.8 git://git.linuxcnc.org/git/linuxcnc.git linuxcnc-2.6.8-3.8.13
cp /usr/src/linux-3.8.13/usr/include/linux/version.h /usr/src/linux-3.8.13/include/linux/version.h
sudo gedit /usr/src/linuxcnc-2.6.8-3.8.13/src/hal/Submakefile
riadok $(Q)$(CC) $(LDFLAGS) -Wl,-soname,$(notdir $@) -shared -o $@ $^
nahradiť $(Q)$(CC) $(LDFLAGS) -Wl,-rpath=/usr/realtime-3.8.13-2/lib -L/usr/realtime-3.8.13-2/lib -llxrt -lpthread -Wl,-soname,$(notdir $@) -shared -o $@ $^ $(RT_LDFLAGS)
cd linuxcnc-2.6.8-3.8.13
git checkout v2.6.8
cd src
./autogen.sh
./configure --prefix=/usr --with-kernel-headers=/usr/src/linux-3.8.13
make
make install
Kontakt :
0905 345640, 038 5321321
ivan.saliga@uhliky.sk.